ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 58 / 228

ID-FLX Lite Global Guide

5.15 Functions

5.15.1 Engine operation states

Engine state

Meaning

Init

Auto test during controller power on

Not ready

Engine is not ready to start

Prestart

Prestart time (page 115)

sequence in process, Prestart output is closed

Cranking

Engine is cranking

Pause

Pause between start attempts

Starting

Starting speed is reached and the

Idle time (page 118)

is running

Running

Engine is running

Stop

Stop

Shutdown

Shut-down alarm activated

Ready

Engine is ready to run

Cooling

Engine is cooling before stop

EmergMan

Emergency Manual engine operation

AfterCool

Engine after cooling - Cooling Pump output is closed

5.15.2 OFF mode

No start of the engine is possible. Outputs STARTER and FUEL SOLENOID are not energized. No reaction if

START, STOP buttons are pressed.

5.15.3 MAN mode

START – starts the engine.

STOP – stops the engine.

Note:

The engine can run without load unlimited time.

The controller does not automatically stop the running engine in MAN mode.

The controller does not start the engine when binary input REM START/STOP is closed.

5.15.4 Start-stop sequence (simplified)

MODE = MAN (Engine start/stop request is given by pressing buttons START and STOP)

MODE = AUT (Engine start/stop request is given by binary input REM START/STOP)

State

Condition of the transition

Action

Next state

Ready

Start request

PRESTART on

Prestart time counter

started

Prestart

RPM >2 or Oil pressure detected or D+ is active

Stop (Stop fail)

OFF mode selected or Shut down alarm active

Not Ready

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды