ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 201 / 228

ID-FLX Lite Global Guide

201

Related FW

2.5.0

Related applications

Comm object

Description

Output is active for 1 second after

activation. This signal is sent to ECU in case

of engine stop request.

Stop Pulse

back to List of LBO

Related FW

2.5.0

Related applications

N/A

Comm object

1663

Description

Activation times prior to engine start:

If measured temperature is equal to PreheatTemp1 (°C) or lower, the LBO Preheat activates prior to

the engine start for time equal to value in setpoint PreheatTime1 (s)

If measured temperature is PreheatTemp2 (°C) or higher, the LBO Preheat activates prior to the

engine start for time equal to value in setpoint PreheatTime2 (s)

If the temperature is between the values, the LBO Preheat activates for time calculated by linear

approximation

The LBO Preheat is activated before engine start as same as

Prestart (page 202)

Preglow (page

202)

, the time is defined by new setpoints (PreheatTime1/2, PreheatTemp1/2) described below.

Activation of

Preheat (page 201)

has a variable activation time based on the measured temperature –

it can be activated either before or after Prestart LBO and is deactivated during cranking.

Input for temperature measurement is selected by setpoint – PreheatSensor which is described

bellow

In case of invalid value on selected AIN, the LBO preheat will activate for time given by setpoint

PreheatTime2 = longest preheat time

Preheat

back to List of LBO

Related FW

2.5.0

Related applications

Comm object

Description

The output closes after reaching value of CrankRPM, fixed 30 RPM. The output opens after stopping of the

engine or in pause during repeated start.

Ignition

back to List of LBO

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды