ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 106 / 228

ID-FLX Lite Global Guide

106

Group: Communication settings

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

Step

Comm object

24537

Related applications

Description

It is controller’s identification number. It is possible to set controller address different from the default value 1

so that more ID-Lite controllers can be interconnected (via RS485) and accessed e.g. from Modbus terminal.

Adresses

1 .. 32

Note:

When opening connection to the controller its address has to correspond with the setting in PC

tool.

ControllerAddr

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[DIRECT / MODEM / MODBUS / ECU LINK]

Default value

Step

Comm object

24522

Related applications

Description

Communication protocol switches for the COM1 channel.

DIRECT

LiteEdit communication protocol via direct cable or AirGate, WebSupervisor

communication protocol via AirGate.

MODEM

LiteEdit communication protocol via modem.

MODBUS

Modbus protocol. See detailed description in

InteliDrive Communication Guide

ECU link

Protocol for communication with Cummins engines via Modbus.

Note:

For details on communication speed and other technical parameters please

see Technical data

on page 90

For detail description see chapter Modbus protocol.

COM1 Mode

back to List of setpoints

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды