ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 110 / 228

ID-FLX Lite Global Guide

110

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

Step

Comm object

24363

Related applications

Description

Name of APN access point for GPRS network.

Note:

This information shall provide your telecommunication operator.

APN Name

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

Step

Comm object

24361

Related applications

Description

User name for APN access point.

Note:

This information shall provide your telecommunication operator.

APN User Name

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

Step

Comm object

24360

Related applications

Description

User password for APN access point.

Note:

This information shall provide your telecommunication operator.

APN User Pass

back to List of setpoints

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды