ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 114 / 228

ID-FLX Lite Global Guide

114

Group: Engine parameters

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

5 .. 1500 [RPM]

Default value

350 RPM

Step

Comm object

9095

Related applications

Description

“Firing” speed when ID-Lite controller stops cranking (starter goes OFF).

Sd Underspeed protection is activated when RPM drops back below the Starting RPM for more than 5

second the engine starting procedure.

Note:

Limit is ignored when Gear teeth = 0 i.e. in engine operation without speed pickup (running state is

indicated from D+ or Starting POil.

Note:

Can appears during "Cranking state" i.e. Starter (or J1939 Start command) is activated then one

running condition was detected (D+ was activated or (POil > Starting POil) condition was filled) - i.e.

Starter was switched off based on previous condition and within time (Cranking time and fix 5 s)

minimum RPM does not appear (RPM > Starting RPM), then is activated RPM meas fail.

Starting RPM

back to List of setpoints

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0.0 .. 100.0 [Bar]

Default value

4.5

Step

0.1

Comm object

9681

Related applications

Description

Controller stops cranking (starter goes OFF) when Oil Pressure (typically measured on AIN1) is over

Starting POil.

Note:

Oil Pressure can be also measured on binary sensor. Then is necessary adjust AIN1 as Binary

input and Starting POil=1.

Note:

There are three conditions for stop cranking:

Starting RPM (page 114)

(just in case the Gear

teeth > 0), StartingPOil and D+ (if enabled). Starter goes off when any of these conditions is valid.

Starting POil

back to List of setpoints

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды