ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 88 / 228

ID-FLX Lite Global Guide

ECU shall show ####, but no alarm is displayed. The output ECU CommOK follows the real situation that

means it is not active anytime when the ECU does not communicate.

The

closes at the beginning of prestart and opens if the engine shall be stopped.

The engine is started via standard contact output or via CAN bus.

Value name

Short name

Dimension

Type

Frame name

EngOil Filter Diff.Press

OilDiffPres

bar

ANA

Amber Warning Lamp

AmberWrnLamp

BIN

DM1

Malfunction Lamp

MalfunctLamp

BIN

DM1

Protect Lamp

ProtectLamp

BIN

DM1

Red Stop Lamp

RedStopLamp

BIN

DM1

Engine speed

RPM

ANA

EEC1

Engine Oil Pressure

EngOil Press

bar

ANA

EFLP1

Coolant Temp

°C

ANA

AT1

Total Engine Hours

EngineHours

ANA

Boost Pressure

Boost Press

bar

ANA

Intake Manifold Temp

Intake Temp

°C

ANA

Practical examples of values read from ECU

If Cummins-Modbus x.x option is selected, following values are read from Modbus Register Data (for QSX15,

QSK45, QSK60):

Value name

Short name

Dimension

Type

Frame name

Red Shutdown Lamp

Red Lamp

BIN

10005

Yellow Warning Lamp

Yellow Lamp

BIN

10006

Engine Speed

RPM

ANA

30001

Coolant Temp

°C

ANA

30002

Oil Pressure (psig)

Oil Press

bar

ANA

30003

Oil Pressure (psia)

Oil Press

bar

ANA

30003

Running Time

ANA

30008

Fuel Rate (UK)

Fuel

L/h

ANA

30018

Fuel Rate (US)

Fuel

L/h

ANA

30018

Intake Manifold Press

Intake Press

bar

ANA

30530

Intake Manifold Temp

Intake Temp

°C

ANA

30531

8.6 ECU Analog inputs

Reading of mentioned values from ECU enables to use analog inputs of the unit for other purposes, e.g.

measuring, displaying and alarm activation related to various quantities. The configuration thus allows using

nine analog inputs on the central unit and four analog inputs on plug-in module if connected.

If the engine without ECU is controlled by ID-Lite, the first analog input is permanently configured to Oil

Pressure, other analog inputs remain freely configurable.

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды