ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 39 / 228

ID-FLX Lite Global Guide

Analog inputs 1, 2, 3, 8 and 9 has separate set points for two levels alarm setting and delay for activation of

alarm.

Analog input 4, 5, 6 and 7 has special „window“ protection. It is possible to adjust Low and High level with alarm

setting Wrn and Sd for each of level. Two delay setpoints are adjustable for Low and High level. (See Practical

example below)

Window protection is necessary to adjust in Modify->Alarm properties->Direction.

Analog input alarm levels and delay adjust in Engine protect group of Setpoints.

Note:

In Alarm list and History is displayed only Wrn and Sd for matching analog input. There isnt visible

direction of protection Low or High.

Practical example of - Class C - Window protection:

Pressure sensor is configured on the analog input 7 and is placed on the intake pipe. There are needed two level

protection. Low level protection against suction from the tank without liquid, that could destroy pump. High level

protection against high liquid pressure in pipe, which could destroy filters against impurity installed between

tank and pump.

AIN7 LowWrn = 2 bar

AIN7 LowSd = 1 bar

AIN7 LowDel = 5 s

AIN7 HighWrn = 4 bar

AIN7 HighSd = 5 bar

AIN7 HighDel = 2 s

Note:

Class C protection is working and LowWrn, LowSd, LowDel, HiWrn, HiSd, HiDel setpoints are visible

only when corresponding AIN is configured in Modify->Alarm properties-> Direction-> Window prot.

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды