ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 10 / 228

ID-FLX Lite Global Guide

• The SNMP protocol (port UDP/161) version 1,2 is not encrypted. Thus it is intended to be used only in closed

private network infrastructures.

• Avoid exposing the port UDP/161 to the public Internet.

1.4 Document history

Revision number

SW version

Date

Author

2.5.0

11.10.2019

Lukáš Bečka

2.3.0

4.10.2019

Lukáš Bečka

2.3.0

17.4.2019

Lukáš Bečka

2.3.0

28.3.2019

Lukáš Bečka

2.3.0

25.3.2019

Petr Weinfurt

2.3.0

13.3.2018

Petr Weinfurt

2.2.0

19.1.2016

Petr Weinfurt

2.1.0

9.11.2015

Zdeněk Rojka

1.9.0

17.12.2014

Jaroslav Juriga

1.8.0

13.5.2014

Jaroslav Juriga

1.7.0

5.5.2013

Jaroslav Juriga

Note:

ComAp believes that all information provided herein is correct and reliable and reserves the right to

update at any time. ComAp does not assume any responsibility for its use unless otherwise expressly

undertaken.

1.5 Language support

ID-Lite controllers support different languages. In default setting of controller are accessible two languages

English, which isn’t possible remove and Chinese. In the controller is possible to substitute Chinese language

by next language via LiteEdit (see the table below). These languages are possible modify via Translator tool in

LiteEdit.

Following language code pages are supported:

Code page

Language

Windows code

West European languages

Windows 1252

134

Chinese

GB 2312

161

Greek

Windows 1253

162

Turkish

Windows 1254

177

Hebrew

Windows 1255

204

Russian

Windows 1251

238

East European languages

Windows 1250

back to Document history

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды