Cisco aironet 1130 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 184

background image

73

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

VLAN Transparent

This feature determines how a mesh access point handles
VLAN tags for Ethernet bridged traffic.

Note

Refer to the

“Configuring Advanced Features”

section on page 97

for overview and additional

configuration details.

If VLAN Transparent is enabled, then VLAN tags are not
handled and packets are bridged as untagged packets.

Note

No configuration of Ethernet ports is required
when VLAN transparent is enabled. The Ethernet
port passes both tagged and untagged frames
without interpreting the frames.

If VLAN Transparent is disabled, then all packets are
handled according to the VLAN configuration on the port
(trunk, access, or normal mode).

Note

If the Ethernet port is set to Trunk mode, then
Ethernet VLAN tagging must be configured. Refer
to

“Using the GUI to Enable Ethernet Bridging”

section on page 78

.

Note

For an overview of normal, access, and trunk
Ethernet port use, refer to the

“Ethernet Port Notes”

section on page 99

.

Note

To use VLAN tagging, you must uncheck the
VLAN Transparent check box.

Note

VLAN Transparent is enabled as a default to ensure
a smooth software upgrade from 4.1.192.xxM
releases to release 5.2. Release 4.1.192.xxM does
not support VLAN tagging (see

Default:

Enabled.

Security Mode

Defines the security mode for mesh access points:
Pre-Shared Key (PSK) or Extensible Authentication
Protocol (EAP).

Note

EAP must be selected if external MAC filter
authorization using a RADIUS server is
configured.

Note

Local EAP or PSK authentication is performed
within the controller if the External MAC Filter
Authorization parameter is disabled (check box
unchecked).

Options:

PSK or EAP

Default:

EAP

Table 12

Global Mesh Parameters (continued)

Parameter

Description

«
...
71
72
73
74
75
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: Xantrex Страницы: 8

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: LogLogic Страницы: 30

Бренд: Mercusys Страницы: 35

Бренд: protech Страницы: 95

Бренд: E-LINX Страницы: 24

Бренд: Z-Wave Страницы: 6

Бренд: Patton electronics Страницы: 13

Бренд: Angel Cool Страницы: 2

Бренд: Belkin Страницы: 2

Бренд: Cameo Страницы: 23

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

Бренд: US Robotics Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды