Cisco aironet 1130 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 184

background image

58

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

a.

Configure a backup controller. Refer to

“Configuring Backup Controllers” procedure on

5.

Configure external authentication of MAC addresses using an external RADIUS server. Refer to the

“Configuring External Authentication and Authorization Using a RADIUS Server” section on
page 68

6.

Configure global mesh parameters. Refer to the

“Configuring Global Mesh Parameters” section on

7.

Configure local mesh parameters. Refer to the

“Configuring Local Mesh Parameters” section on

8.

Configure antenna parameters. Refer to the

“Configuring Antenna Gain” section on page 92

9.

Configure the DCA channels for the mesh access points. Refer to the

“Configuring Dynamic

Channel Assignment” section on page 94

for details.

10.

Configure mobility groups (if desired) and assign controllers. Refer to Chapter 12, “Configuring
Mobility Groups” in the

Cisco Wireless LAN Controller Configuration Guide, Release 5.2

at:

http://www.cisco.com/en/US/products/ps6366/products_installation_and_configuration_guides_list.html

11.

Configure Ethernet Bridging (if desired). Refer to the

“Configuring Ethernet Bridging” section on

12.

Configure advanced features such Ethernet VLAN tagging network, video and voice. Refer to the

“Configuring Advanced Features” section on page 97

.

Adding MAC Addresses of Mesh Access Points to MAC Filter

You must enter the MAC address for all mesh access points that you want to use in the mesh network
into the appropriate controller. A controller only responds to discovery requests from outdoor radios that
appear in its authorization list. MAC filtering is enabled by default on the controller, so only the MAC
addresses need to be configured. If the Access Point has an SSC and has been added to the AP
Authorization List, then the MAC address of the AP need not be added to the MAC Filtering List.

You can add the mesh access point using either the GUI or the CLI.

Note

You can also download the list of mesh access point MAC addresses and push them to the controller
using Cisco WCS. Refer to the

Cisco Wireless Control System Configuration Guide, Release 6.0

:

http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/WCS60cg.html

Using the GUI to Add the MAC Address of the Mesh Access Point to the Controller Filter List

Follow these steps to add a MAC filter entry for the mesh access point on the controller using the
controller GUI.

Step 1

Click

Security

>

AAA

>

MAC Filtering

. The MAC Filtering window appears (see

«
...
56
57
58
59
60
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

i-bus KNX IPR/S 3.5.1

Бренд: ABB Страницы: 44

Бренд: XMG Страницы: 5

Бренд: Habitat Страницы: 48

Бренд: NAD Страницы: 2

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

Бренд: DataRemote Страницы: 2

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: Konica Minolta Страницы: 38

Бренд: Western Digital Страницы: 8

Бренд: ZALMAN Страницы: 9

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: WAGO Страницы: 2

Бренд: StarTech.com Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды