Cisco aironet 1130 Скачать руководство пользователя страница 87

Страница: 87 / 184

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Table 14

identifies mesh access points and their respective frequency bands that support WGB.

Note

In the above table, X means Supported and — means Not Supported.

Configuration Guidelines

For the AP1522 or AP1524PS and Cisco 3200 to interoperate on the public safety network, the following
configuration guidelines must be met:

•

Client access must be enabled on the backhaul (Mesh global parameter). This feature is not
supported on the AP1524PS.

•

Public safety must be enabled globally on all mesh access points (MAPs) in the mesh network.

•

Channel number assignment on the AP1522 or AP1524PS must match those on the Cisco 3200 radio
interfaces.

–

Channels 20 (4950 GHz) through 26 (4980 GHz) and sub-band channels 1-19 (5 and 10 MHz)
are used for Cisco 3200 interoperability. This configuration change is made on the controller.
No changes are made to the mesh access point configuration.

–

Channel assignments are only made to the RAP. Updates to the MAP are propagated by the RAP.

The default channel width for Cisco 3200s is 5 MHz. You must

either

change the channel width to 10 or

20-MHz to enable WGBs to associate with the AP1522 and AP1524PS

change the channel on the

AP1522 or AP1524PS to a channel in the 5-MHz (channels 1 to 10) or 10-MHz band (channels 11 to 19).

•

Radio (802.11a) must be disabled when configuring channels and then re-enabled when using the
CLI.

–

When using the GUI, enabling and disabling of the 802.11a radio for channel configuration is
not required.

•

Cisco 3200s can scan channels

within

but not across the 5, 10 or 20-MHz bands.

Model c3205 is a Cisco 3200 with a 802.11a radio (5.8-GHz sub-band).

Table 14

WGB Interoperability Chart

RAP/MAP (5-GHz
Backhaul)

WGB

3200

1240

1130

1310

4.9-GHz
(5, 10, 20
MHz)

5-GHz

2.4-GHz

5-GHz

2.4-GHz

5-GHz

2.4-GHz

1524PS/1524PS

—

1522/1522

1524PS/1522

—

1522/1524PS

—

1240/1130

—

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды