Cisco aironet 1130 Скачать руководство пользователя страница 71

Страница: 71 / 184

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Configuring Global Mesh Parameters

This section provides instructions for configuring the mesh access point to establish a connection with
the controller including:

•

Setting the maximum range between RAP and MAP (not applicable to AP1130 and AP1240)

•

Enabling a backhaul to carry client traffic

•

Defining if VLAN tags are forwarded or not

•

Defining the authentication mode (EAP or PSK) and method (local or external) for mesh access
points including security settings (local and external authentication).

You can configure the necessary mesh parameters using either the GUI or the CLI. All parameters are
applied globally.

Using the GUI to Configure Global Mesh Parameters

To configure global mesh parameters using the controller GUI, follow these steps.

Step 1

Click

Wireless

Mesh

(see

Figure 44

Figure 44

Mesh Window

Step 2

Modify the mesh parameters as appropriate.

Table 12

describes each parameter.

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды