Cisco aironet 1130 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 184

background image

16

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Mesh Network Components

Regulatory Domains

For information on the channels and maximum power levels of the AP1520 supported within the world's
regulatory domains refer to the

Channels and Maximum Power Settings for Cisco Aironet Lightweight

Access Points

manual at:

http://www.cisco.com/en/US/docs/wireless/access_point/channels/lwapp/reference/guide/1520_chp.html

Frequency Bands

The 2.4 GHz and 5 GHz frequency bands are supported on the AP1130, AP1240 and AP1520 radios.
Additionally, the 4.9 GHz public safety band is supported on the AP1524. (See

.)

Figure 7

Frequency Bands Supported By 802.11a Radios on AP1520s

The 5 GHz band is a conglomerate of three bands in the USA: 5.150 to 5.250 (UNII-1), 5.250 to 5.350
(UNII-2), 5.470 to 5.725 (UNII-2 Extended), and 5.725 to 5.850 (ISM). UNII-1 and the UNII-2 bands
are contiguous and are indeed treated by 802.11a as being a continuous swath of spectrum 200MHz
wide, more than twice the size of the 2.4GHz band.

The 4.9 GHz is a public safety channel within the 5-MHz (channels 1 to 10), 10-MHz (channels 11-19),
and 20-MHz (channels 20-26) bandwidths.

RF-2

Slot 3

Disabled in this release.

1.

If all LEDs are off, the access point has no power.

2.

When the access point power supply is initially turned on, all LEDs are amber.

Table 2

Access Point LED Signals (continued)

LED

Color

1

,

2

Meaning

«
...
14
15
16
17
18
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: Paradyne Страницы: 22

Бренд: Niveo Страницы: 155

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Alesis Страницы: 61

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: Dolphin Страницы: 9

Бренд: TP-Link Страницы: 110

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

ControlPoint 2000

Бренд: 4Home Страницы: 20

Бренд: B&B Electronics Страницы: 2

Elinx EIR510 Series

Бренд: B&B Electronics Страницы: 2

Бренд: Casablanca Страницы: 13

Kontron SMARC-sXEL

Бренд: S&T Страницы: 108

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

See3CAM 30 Z10X

Бренд: e-con Systems Страницы: 14

Бренд: Watchguard Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды