Cisco aironet 1130 Скачать руководство пользователя страница 88

Страница: 88 / 184

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Using the GUI to Enable AP1522 and AP1524PS to Associate with Cisco 3200

To enable AP1522 and AP1524PS to associate with Cisco 3200, follow these steps.

Step 1

To enable the backhaul for client access, click

Wireless > Mesh

to access the Mesh window.

Step 2

Check the Backhaul Client Access

Enabled

check box to allow wireless client association over the

802.11a radio. Click

Apply

Note

You are prompted with a message to allow reboot of all the mesh access points to enable
Backhaul Client Access on a network. Click

Step 3

To assign the channel to use for the backhaul (channels 20 through 26), click

Wireless > Access Points

> Radio

and select

802.11a/n

from the Radio sub-heading. A summary window for all 802.11a radios

displays.

Step 4

At the Antenna drop-down menu for the appropriate RAP, select

Configure.

The window seen in

Figure 56

displays.

Figure 56

Wireless > Access Points > Radio > 802.11 a/n > Configure Window

Step 5

At the RF Backhaul Channel Assignment section, select the

Custom

option for the Assignment Method

option and select any channel between 1 and 26.

Step 6

Click

Apply

to commit your changes.

Step 7

Click

Save Configuration

to save your changes.

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды