Cisco aironet 1130 Скачать руководство пользователя страница 120

Страница: 120 / 184

120

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Checking the Health of the Network

Show Mesh Commands

The show mesh commands are grouped under the following headings:

•

Viewing General Mesh Network Details, page 120

•

Viewing Mesh Access Point Details, page 122

•

Viewing Public Safety Setting, page 124

•

Viewing Security Settings and Statistics, page 124

To view a summary of possible

show mesh

commands, enter this command:

(Cisco Controller) >

show mesh ?

env Show mesh environment.

backhaul Show mesh AP backhaul info.

neigh Show AP neigh list.

path Show AP path.

astools show mesh astools list

stats Show AP stats.

secbh-stats Show Mesh AP secondary backhaul stats.

per-stats Show AP Neighbor Packet Error Rate stats.

queue-stats Show AP local queue stats.

security-stats Show AP security stats.

ap Show mesh ap summary

config Show mesh configurations.

secondary-backhaul Show mesh secondary-backhaul

ids-state Show mesh ids-state

client-access Show mesh backhaul with client access.

public-safety Show mesh public safety.

background-scanning Show mesh background-scanning state.

cac Show mesh cac.

Viewing General Mesh Network Details

•

show mesh env

{

summary

AP_name

}

—

Shows the temperature, heater status, and Ethernet status

for either all access points (summary) or a specific access point (

AP_name

). The access point name,

role (RootAP or MeshAP), and model are also shown.

–

The temperature is shown in both Fahrenheit and Celsius.

–

The heater status is ON or OFF.

–

The Ethernet

status is UP or DOWN

Note

Battery status appears as N/A (not applicable) in the

show mesh env

AP_name

status display

because it is not provided for access points.

controller >

show mesh env summary

AP Name Temperature(C/F) Heater Ethernet Battery

------------------ ---------------- ------ -------- -------

SB_RAP1 39/102 OFF UpDnNANA N/A

SB_MAP1 37/98 OFF DnDnNANA N/A

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды