Cisco aironet 1130 Скачать руководство пользователя страница 165

Страница: 165 / 184

165

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Adding and Managing Mesh Access Points with Cisco WCS

Figure 99

Mesh AP Detail Window

Step 5

At the Access Point configuration window, follow these steps to view configuration details for the mesh
access point.

Choose the

General

tab to view the overall configuration of the mesh access point such as AP name,

MAC address, AP Up time, associated controllers (registered and primary) operational status, and
software version.

Note

The software version for mesh access points is appended the letter

and the word

mesh

parentheses.

Choose the

Interface

tab to view configuration details for the interfaces supported on the mesh

access point. Interface options are radio and Ethernet.

Choose the

Mesh Links

tab to view parent and neighbors’ details (name, MAC address, packet error

rate, and link details) for the mesh access point. You can also initiate link tests from this panel.

Choose the

Mesh Statistics

tab to view details on the bridging, queue, and security statistics for the

mesh access point. For more details on mesh statistics, refer to the

“Mesh Statistics for a Mesh

Access Point” section on page 171

Monitoring Mesh Access Point Neighbors Using Maps

To view details on neighbors of a mesh access point from a mesh network map, follow these steps.

Step 1

Choose

Monitor > Maps

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды