Cisco aironet 1130 Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 184

background image

170

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Adding and Managing Mesh Access Points with Cisco WCS

Table 24

Monitor Access Points Additional Search Results Parameters

Column

Options

AP Type

Indicates the type of access point (unified or autonomous).

Antenna Azim. Angle

Indicates the horizontal angle of the antenna.

Antenna Diversity

Indicates if antenna diversity is enabled or disabled. Antenna
diversity refers to the access point sampling the radio signal from
two integrated antenna ports in order to choose the preferred
antenna.

Antenna Elev. Angle

Indicates the elevation angle of the antenna.

Antenna Gain

The peak gain of the dBi of the antenna for directional antennas and
the average gain in dBi for omni-directional antennas connected to
the wireless network adapter. The gain is in multiples of 0.5 dBm.
An integer value 4 means 4 x 0.5 - 2 dBm of gain.

Antenna Mode

Indicates the antenna mode such as omni, directional, or
non-applicable.

Antenna Name

Indicates the antenna name or type.

Antenna Type

Indicates whether the antenna is internal or external.

Audit Status

Indicates one of the following audit statuses:

•

Mismatch—Config differences were found between Cisco
WCS and controller during the last audit.

•

Identical—No config differences were found during the last
audit.

•

Not Available—Audit status is unavailable.

Bridge Group Name

Indicates the name of the bridge group used to group the access
points, if applicable.

CDP Neighbors

Indicates all directly connected Cisco devices.

Channel Control

Indicates whether the channel control is automatic or custom.

Channel Number

Indicates the channel on which the Cisco radio is broadcasting.

Controller Port

Indicates the number of controller ports.

Node Hops

Indicates the number of hops between access point.

POE Status

Indicates the Power-over-Ethernet status of the access point. The
possible values include:

•

Low—The access point draws low power from the Ethernet.

•

Lower than 15.4 volts—The access point draws lower than 15.4
volts from the Ethernet.

•

Lower than 16.8 volts—The access point draws lower than 16.8
volts from the Ethernet.

•

Normal—The power is high enough for the operation of the
access point.

•

Not Applicable—The power source is not from the Ethernet.

Primary Controller

Indicates the name of the primary controller for this access point.

«
...
168
169
170
171
172
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: N-Tron Страницы: 101

Бренд: XDS Страницы: 99

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Бренд: M-Audio Страницы: 10

Бренд: Datasat Страницы: 32

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Бренд: Yamaha Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды