Cisco aironet 1130 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 184

background image

82

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Note

Refer to the “Cisco Workgroup Bridges” section in Chapter 7 of the

Cisco Wireless LAN Controller

Configuration Guide, Release 6.0

for configuration steps at:

http://www.cisco.com/en/US/products/ps6366/products_installation_and_configuration_guides_list.html

Supported Workgroup Bridge Modes and Capacities

•

The 1130, 1240, and 1310 autonomous mesh access points must be running Cisco IOS release
12.4(3g)JA or later (on 32-MB access points) or Cisco IOS release 12.3(8)JEB or later (on 16-MB
access points). Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.

Note

If your mesh access point has two radios, you can only configure workgroup bridge mode
on one of the radios. Cisco recommends that you disable the second radio. Workgroup bridge
mode is not supported on access points with three radios such as the AP1524.

•

Client mode WGB (BSS) is supported; however, infrastructure WGB is not supported. The client
mode WGB is not able to trunk VLANs as is an infrastructure WGB.

•

Multicast traffic is not reliably transmitted to WGB because no ACKs are returned by the client.
Whereas, multicast traffic is unicast to infrastructure WGBs and ACKs are received back.

•

If one radio is configured as WGB in an IOS access point, then the second radio cannot be a WGB
or a Repeater.

•

Mesh access points can support up to 200 clients including wireless clients, WGBs, and wired
clients behind the associated WGBs.

•

WGBs operating with Cisco IOS release 12.4(3g)JA

cannot associate with mesh access points if the

WLAN is configured with WPA1 (TKIP) +WPA2 (AES), and the corresponding WGB interface is
configured with only one of these encryptions (either WPA1 or WPA2).

–

displays WPA security settings for WGB (controller GUI).

–

displays WPA-2 security settings for WGB (controller GUI).

Figure 49

WPA Security Settings for WGB

«
...
80
81
82
83
84
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: Cambium Networks Страницы: 29

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 16

Бренд: Patton electronics Страницы: 51

Бренд: Salto Страницы: 2

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Surround Dongle

Бренд: Sennheiser Страницы: 18

Бренд: Zoom Страницы: 88

Бренд: Digi Страницы: 116

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

Бренд: Comet Labs Страницы: 11

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

GEFORCE RTX 4090

Бренд: Nvidia Страницы: 160

Бренд: ADTRAN Страницы: 4

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: Doro Страницы: 50

Бренд: ENERMAX Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды