Cisco aironet 1130 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 184

background image

99

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Ethernet Port Notes

•

Ethernet VLAN tagging allows Ethernet ports to be configured as normal, access, or trunk in both
indoor and outdoor implementations.

Note

When VLAN Transparent is disabled, the default Ethernet port mode is normal. VLAN
Transparent must be disabled for VLAN tagging to operate and to allow configuration of
Ethernet ports. To disable VLAN Transparent, a global parameter, refer to

Global Mesh Parameters” section on page 71

–

Normal mode–In this mode, the Ethernet port does not accept or send any tagged packets.
Tagged frames from clients are dropped.

Use the normal mode in applications when only a single VLAN is in use or there is no need to
segment traffic in the network across multiple VLANs.

–

Access Mode–In this mode, only untagged packets are accepted. All incoming packets are
tagged with user-configured VLANs called access-VLAN.

Use the access mode for applications in which information is collected from devices connected
to the MAP such as cameras or PCs and then forwarded to the RAP. The RAP then applies tags
and forwards traffic to a switch on the wired network.

–

Trunk mode–This mode requires the user to configure a native VLAN and an allowed VLAN
list (no defaults). In this mode, both tagged and untagged packets are accepted. Untagged
packets are accepted and are tagged with the user-specified native VLAN. Tagged packets are
accepted if they are tagged with a VLAN in the allowed VLAN list.

–

Use the trunk mode for bridging applications such as forwarding traffic between two MAPs
resident on separate buildings within a campus.

•

Ethernet VLAN tagging operates on Ethernet ports that are not used as backhauls.

Ethernet VLAN Tagging Guidelines

•

For security reasons the Ethernet port on a mesh access point (RAP and MAP) is disabled by default.
It is enabled by configuring Ethernet Bridging on the mesh access point port.

•

Ethernet bridging must be enabled on all the mesh access points in the mesh network to allow
Ethernet VLAN tagging to operate.

•

VLAN mode must be set as non-VLAN transparent (global mesh parameter). Refer to

CLI to Configure Global Mesh Parameters” section on page 75

–

VLAN transparent is enabled by default. To set as non-VLAN transparent you must uncheck the
VLAN transparent option in the global mesh parameters window (see

).

«
...
97
98
99
100
101
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: D-Link Страницы: 13

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: M86 Security Страницы: 46

Бренд: TP-Link Страницы: 3

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренд: Xantech Страницы: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Бренд: Juniper Страницы: 122

Бренд: ebm-papst Страницы: 13

Бренд: Rolls Страницы: 1

CloudGen Firewall

Бренд: Barracuda Страницы: 8

Бренд: Ebyte Страницы: 23

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: TRENDnet Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды