Cisco 901 Скачать руководство пользователя страница 62

Страница: 62 / 218

1-48

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

ethernet oam remote-failure action

To enable Ethernet Operations, Administration, and Maintenance (OAM) remote failure actions, use the

ethernet oam remote-failure action

command in interface configuration mode. To turn off remote

failure actions, use the

form of this command.

ethernet oam remote-failure

{

critical-event

dying-gasp

link-fault

}

action

error-disable-interface

no ethernet oam remote-failure

{

critical-event

dying-gasp

link-fault

}

action

Syntax Description

Command Default

Actions in response to Ethernet OAM remote failures do not occur.

Command Modes

Interface configuration (config-if)

Command History

Usage Guidelines

Use this command to configure an interface to take specific actions when Ethernet OAM remote-failure
events occur.

Release 15.1(2)SNG does not support sending critical-event messages but can receive all three message
types.

Examples

The following example shows how to configure the action that the Ethernet 1/1 interface takes when a
critical event occurs:

Router#

configure terminal

Router(config)#

interface ethernet 1/1

Router(config-if)#

ethernet oam remote-failure critical-event action

error-disable-interface

critical-event

Specifies remote critical event failures.

dying-gasp

Specifies remote dying-gasp failures.

link-fault

Specifies remote link-fault failures.

error-disable-interface

Disables the interface when an error occurs.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды