Cisco 901 Скачать руководство пользователя страница 182

Страница: 182 / 218

1-168

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show platform hardware

To display the status of hardware devices on the Cisco ASR 901, use the

show platform hardware

command. The command displays information about hardware devices on the Cisco ASR 901 for
troubleshooting and debugging purposes.

show platform hardware {adrian | bits | cpld | cpu | ethernet | fio | hwic | rtm | stratum | ufe

winpath

Syntax Description

Command Modes

Privileged EXEC

Command History

Related Commands

adrian

Displays information about the adrian hardware.

bits

Displays information about the BITS hardware.

cpld

Displays information about the CPLD hardware.

cpu

Displays information about the CPU.

ethernet

Displays information about the ethernet interfaces on the Cisco ASR 901.

fio

Displays information about the FIO fpga hardware.

hwic

Displays information about the HWICs installed on the Cisco ASR 901.

rtm

Displays information about the RTM Module (ASM-M2900-TOP daughter card).

stratum

Displays information about the stratum hardware.

ufe

Displays information about the UFE hardware.

winpath

Displays information about the Winpath hardware.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

show controller

Displays the status of system controllers.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды