Cisco 901 Скачать руководство пользователя страница 211

Страница: 211 / 218

1-197

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

synce state slave

To configure the synchronous ethernet copper port as slave, use the

synche state slave

command. Use

the

form of the command to disable the configuration.

synce state slave

no synce state slave

Syntax Description

This command has no arguments.

Command Default

None.

Command Modes

Interface configuration mode.

Command History

Usage Guidelines

The

synce state slave

command configures the synchronous ethernet copper port as the slave in the

interface configuration mode.

Examples

The following command configures the ethernet copper port as slave:

Router(config-if)#

synce state slave

Related Commands

Release

Modification

15.1(2)SNG

This command was introduced on the Cisco ASR 901 router.

Command

Description

synce state master

Configures the synchronous ethernet copper port as master.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды