Cisco 901 Скачать руководство пользователя страница 41

Страница: 41 / 218

1-27

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

clock-port

Specifies the mode of a PTP clock port.

clock-port

port-name port-role

no clock-port

port-name port-role

Syntax Description

Defaults

This command is disabled by default.

Command Modes

PTP clock configuration mode

Command History

Examples

The following example shows how to configure a PTP clock port.

Router#

config terminal

Router(config)#

ptp clock ordinary domain 0

Router(config-ptp-clk)#

clock-port SLAVE slave

Router(config-ptp-port)#

transport ipv4 unicast interface loopback

Router(config-ptp-clk)#

clock-source 8.8.8.1

Related Commands

name

Specifies a name for the clock port.

port-role

Specifies the role of the clock port, which can be slave or master.

•

slave—Sets the clock port to PTP slave mode; the port exchanges timing
packets with a PTP master device.

•

master—Sets the clock port to PTP master mode; the port exchanges
timing packets with PTP slave devices.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

ptp clock

Creates a PTP clock instance.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды