Cisco 901 Скачать руководство пользователя страница 169

Страница: 169 / 218

1-155

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show ethernet loopback

To display information about the per port Ethernet loopbacks configured on a router or an interface, use
the

show ethernet loopback

command in privileged EXEC mode.

show ethernet loopback active [brief | [

interface-id

] [service-instance

]]

Syntax Description

Command Modes

Privileged EXEC

Command History

Usage Guidelines

If you do not specify an

interface-id,

all configured loopbacks appear. The router supports a maximum

of two Ethernet loopback configurations.

Examples

The following example shows how to verify the configuration:

Router#

show ethernet loopback active

============================================================

Interface : GigabitEthernet0/3

Service Instance : 32

Direction : Terminal

Time out(sec) : 300

Status : on

Start time : 14:15:01.742 IST Tue Jun 18 2013

Time left : 00:04:48

Source Mac Address : 0000.0002.0002

Destination Mac Address : 4055.3989.751c

Related Commands

active

Displays active ethernet loopback sessions.

brief

Displays brief description of the current loopback sessions

interface-id

(Optional) Displays loopback information for the specified interface. Only
physical interfaces support ethernet loopback.

service-instance

Specifies the service instance ID.

Release

Modification

15.2(2)SNG

This command was introduced on the Cisco ASR 901 router.

Command

Description

start ethernet
loopback

stop

ethernet loopback

Starts or stops the loopback operation.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды