Cisco 901 Скачать руководство пользователя страница 92

Страница: 92 / 218

1-78

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

network-clock quality-level

To specify the QL value for line or external timing input or output, use the

network-clock quality-level

command. Use the

form of the command to remove the configuration.

network-clock quality-level {

}

<value>

{interface

<interface name> <slot/port>

| external

<slot/card/port>

| controller

<slot/card/port>

}

no network-clock quality-level

Syntax Description

Command Modes

Interface configuration

Command History

Usage Guidelines

The

network-clock quality-level

command specifies the QL value for line or external timing input or

output. The value is based on a global interworking Option.

•

If Option 1 is configured, the available values are QL-PRC, QL-SSU-A, QL-SSU-B, QL-SEC, and
QL-DNU.

•

If Option 2 is configured with GEN 2, the available values are QL-PRS, QL-STU, QL-ST2,
QL-TNC, QL-ST3, QL-SMC, QL-ST4 and QL-DUS.

•

If option 2 is configured with GEN1, the available values are QL-PRS, QL-STU, QL-ST2, QL-SMC,
QL-ST4 and QL-DUS

This command is not supported for synchronous ethernet interfaces.

Examples

This example specifies the QL value for external timing input:

Router(config-if)#

network-clock quality-level rx QL-PRC external 4/0/0 e1 crc4

interface-name

Specifies the interface.

external

Specifies an external slot/port/card.

controller

Specifies the controller slot/port/card.

value

Value is based on options specified in usage guidelines section.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды