Cisco 901 Скачать руководство пользователя страница 137

Страница: 137 / 218

1-123

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

service-policy (policy-map class)

Examples

The following example creates a hierarchical service policy in the service policy called parent:

Router(config)#

policy-map child

Router(config-pmap)#

class voice

Router(config-pmap-c)#

priority 500

Router(config-pmap-c)#

exit

Router(config-pmap)#

exit

Router(config)#

policy-map parent

Router(config-pmap)#

class class-default

Router(config-pmap-c)#

shape average 10000000

Router(config-pmap-c)#

service-policy child

Related Commands

Command

Description

bandwidth (policy-map class)

Specifies or modifies the bandwidth allocated for a class
belonging to a policy map.

fair-queue

Specifies the number of queues to be reserved for use by a
traffic class.

policy-map

Specifies the name of the service policy to configure.

priority

Gives priority to a class of traffic belonging to a policy
map.

service-policy

Specifies the name of the service policy to be attached to
the interface.

shape

Specifies average or peak rate traffic shaping.

show policy-map

Displays the configuration of all classes for a specified
service policy map or all classes for all existing policy
maps.

show policy-map interface

Displays the configuration of all classes configured for all
service policies on the specified interface or displays the
classes for the service policy for a specific PVC on the
interface.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды