Cisco 901 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 218

background image

1-40

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

encapsulation dot1q (service instance)

encapsulation dot1q (service instance)

To define the matching criteria to map

802.1Q

frames ingress on an interface to the appropriate service

instance, use the

encapsulation dot1q

command in the service instance mode. To delete the matching

criteria to map 802.1Q frames ingress on an interface to the appropriate service instance, use the

no

form

of this command.

encapsulation dot1q

vlan-id

[,

vlan-id

[-

vlain-id

]] [

native

]

no encapsulation dot1q

vlan-id

[,

vlan-id

[-

vlain-id

]] [

native

]

Syntax Description

.

Command Default

No matching criteria are defined.

Command Modes

Service instance

Command History

Usage Guidelines

The criteria for this command are: single VLAN, range of VLANs, and lists of the previous two.

A single 802.1Q service instance, allows one VLAN, multiple VLANs, or a range of VLANs. The native
keyword can only be set if a single VLAN tag has been specified.

Only a single service instance per port is allowed to have the

native

keyword.

Only one encapsulation command may be configured per service instance.

Examples

The following example shows how to map 802.1Q frames ingress on an interface to the appropriate
service instance:

Router(config-if-srv)#

encapsulation dot1q 10

vlan-id

VLAN ID, integer in the range 1 to 4094. Hyphen must be entered to separate the
starting and ending VLAN ID values that are used to define a range of VLAN IDs.
Optional) Comma must be entered to separate each VLAN ID range from the next range.

native

(Optional) Sets the VLAN ID value of the port to the value specified by the

vlan-id

argument.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

«
...
52
53
54
55
56
...
»

Содержание 901



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 901

Бренд: IBM Страницы: 72

Бренд: E-Lins Страницы: 59

Бренд: E-Lins Страницы: 11

Бренд: E-Lins Страницы: 9

Бренд: E-Lins Страницы: 5

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: Black Box Страницы: 37

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: ICP DAS USA Страницы: 8

Бренд: Patton electronics Страницы: 13

Бренд: Angel Cool Страницы: 2

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Modecom Страницы: 16

Бренд: Hamlet Страницы: 11

Бренд: Dantel Страницы: 22

Бренд: NetComm Страницы: 34

OmniTik UPA-5HnD

Бренд: RouterBOARD Страницы: 4

Бренд: Intercel Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды