Cisco 901 Скачать руководство пользователя страница 176

Страница: 176 / 218

1-162

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show mac-address-table

To display the MAC address table, use the show mac-address-table command in privileged EXEC mode.

show mac-address-table [address

mac-addr

] [aging-time

vlan-id

] [count

vlan-id

] [dynamic

[address

mac-address

| interface

type slot/port

| vlan

vlan-id

]] [interface

type/number

]

[multicast [{igmp-snooping | mld-snooping | vlan

vlan-id

}]] [static [[{address

mac-addr

} |

{interface

interface/switch-num//slot/port

} | vlan

vlan-id

] [vlan

vlan-id

]

Syntax Description

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History

Usage Guidelines

The

mac-addr

is a 48-bit MAC address and the valid format is H.H.H.

The

count

keyword displays the number of multicast entries.

The

multicast

keyword displays the multicast MAC addresses (groups) in a VLAN or displays all

statically installed or IGMP snooping-learned entries in the Layer 2 table.

The

dynamic

entries that are displayed in the Learn field are always set to Yes.

Examples

The following example shows the output for the

show mac address-table count

command:

Router#

show

mac address-table count

address

mac-addr

Displays information about the MAC-address table for a specific MAC
address; see the "Usage Guidelines" section for format guidelines.

vlan

vlan-id

(Optional) Displays information for a specific VLAN only. Range: 1 to 4094.

aging-time

Displays information about the MAC-address aging time.

count

Displays the number of entries that are currently in the MAC-address table.

dynamic

Displays information about the dynamic MAC-address table entries only.

interface

interface

(Optional) Displays information about a specific interface type; possible
valid values are gigabitethernet and tengigabitethernet.

multicast

Displays information about the multicast MAC-address table entries only.

igmp-snooping

Displays the addresses learned by Internet Group Management Protocol
(IGMP0 snooping.

mld-snooping

Displays the addresses learned by multicast listener discovery version 2
(MLDv2) snooping.

static

Displays information about the static MAC-address table entries only.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды