Cisco 901 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 218

background image

1-124

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

set cos

set cos

To set the Layer 2 class of service (CoS) value of an outgoing packet, use the

set cos

command in

policy-map class configuration mode. To remove a specific CoS value setting, use the

no

form of this

command.

set cos

{

cos-value

}

no set cos

{

cos-value

}

Syntax Description

Command Default

No CoS value is set for the outgoing packet.

Command Modes

Policy-map class configuration

Command History

Usage Guidelines

CoS packet marking is supported only in the Cisco Express Forwarding switching path.

The

set cos

command should be used by a router if a user wants to mark a packet that is being sent to a

switch. Switches can leverage Layer 2 header information, including a CoS value marking.

The

set cos

command can be used only in service policies that are attached in the output direction of an

interface. Packets entering an interface cannot be set with a CoS value.

The

match cos

and

set cos

commands can be used together to allow routers and switches to interoperate

and provide quality of service (QoS) based on the CoS markings.

Layer 2 to Layer 3 mapping can be configured by matching on the CoS value because switches already
can match and set CoS values. If a packet that needs to be marked to differentiate user-defined QoS
services is leaving a router and entering a switch, the router should set the CoS value of the packet
because the switch can process the Layer 2 header.

Using This Command with the Enhanced Packet Marking Feature

You can use this command as part of the Enhanced Packet Marking feature

to specify the “from-field”

packet-marking category to be used for mapping and setting the CoS value. The “from-field”
packet-marking categories are as follows:

•

Precedence

•

Differentiated services code point (DSCP)

If you specify a “from-field” category but do not specify the

table

keyword and the applicable

table-map-nam

e argument, the default action will be to copy the value associated with the “from-field”

category as the CoS value. For instance, if you configure the

set cos precedence

command, the

precedence value will be copied and used as the CoS value.

cos-value

Specific IEEE 802.1Q CoS value from 0 to 7.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

«
...
136
137
138
139
140
...
»

Содержание 901



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 901

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 34

Бренд: E-Lins Страницы: 59

Бренд: E-Lins Страницы: 11

Бренд: E-Lins Страницы: 9

Бренд: E-Lins Страницы: 5

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: Tripp Lite Страницы: 20

NVIP- NVRA0104/GO

Бренд: Novus Страницы: 44

DSL5068EN(1T1R)

Бренд: Aztech Страницы: 40

Бренд: Gbord Страницы: 8

Бренд: Kontron Страницы: 42

Бренд: Patton electronics Страницы: 2

Бренд: Lanner Страницы: 78

Бренд: ZKTeco Страницы: 68

VMG5313-BXB SERIES

Бренд: ZyXEL Communications Страницы: 2

Бренд: Quantum Страницы: 7

Бренд: ACTi Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды