Cisco 901 Скачать руководство пользователя страница 74

Страница: 74 / 218

1-60

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

mac-flap-ctrl

To identify MAC flaps occurring in the router and to take preventive action, use the

mac-flap-ctrl on

per-mac

command. To remove MAC flap control, use the

form of the command.

mac-flap-ctrl on per-mac

<mac-movement> <time-interval>

no mac-flap-ctrl on per-mac

<mac-movement> <time-interval>

Syntax Description

Command Default

The default values for the counters are five and ten; that is five movements in ten seconds.

Command Modes

Global configuration

Command History

Usage Guidelines

Configure the maximum number of MAC movements that are allowed in a specified time interval,
beyond which the MAC movement is termed as flapping. As preventive action, err-disabling is done in
one of the ports that has MAC flapping.

Once the port is err-disabled, it can be administratively brought up using the

shut

and

no shut

commands.

Examples

The following example sets the maximum number of mac movements to 20 in 10 seconds, before a MAC
flap is detected in the router.

Router(config)#

mac-flap-ctrl on per-mac 20 10

Related Commands

mac-movement

Maximum number of MAC movements that are allowed in the specified
time.

time-interval

Time interval that can elapse before the MAC movements are tagged as
flapping.

Release

Modification

15.1(2)SNI

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

None

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды