Cisco 901 Скачать руководство пользователя страница 205

Страница: 205 / 218

1-191

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show xconnect

Router#

show xconnect all detail

Legend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 State

UP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No HardwareXC

ST Segment 1 S1 Segment 2 S2

------+---------------------------------+--+---------------------------------+--

UP ac Et0/0(Ethernet) UP mpls 10.55.55.2:1000 UP

Interworking: ip Local VC label 16

Remote VC label 16

pw-class: mpls-ip

UP ac Et1/0.1:200(Eth VLAN) UP mpls 10.55.55.2:5200 UP

Interworking: ip Local VC label 17

Remote VC label 20

pw-class: mpls-ip

IA pri ac Et1/0.2:100(Eth VLAN) UP ac Et2/0.2:100(Eth VLAN) UP

Interworking: none Interworking: none

UP sec ac Et1/0.2:100(Eth VLAN) UP mpls 10.55.55.3:1101 UP

Interworking: none Local VC label 23

Remote VC label 17

pw-class: mpls

The additional fields displayed in the detailed output are self-explanatory.

Related Commands

Command

Description

show atm pvc

Displays all ATM PVCs and traffic information.

show atm vc

Displays all ATM PVCs and SVCs and traffic information.

show atm vp

Displays the statistics for all VPs on an interface or for a specific VP.

show connect

Displays configuration information about drop-and-insert
connections that have been configured on a router.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show interfaces

Displays statistics for all interfaces configured on the router or access
server.

show mpls l2transport
binding

Displays VC label binding information.

show mpls l2transport vc

Displays information about AToM VCs that have been enabled to
route Layer 2 packets on a router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды