Cisco 901 Скачать руководство пользователя страница 173

Страница: 173 / 218

1-159

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show ip vrf

To display the set of defined Virtual Private Network (VPN) routing and forwarding (VRF) instances and
associated interfaces, use the

show ip vrf

command in privileged EXEC mode.

show ip vrf

[

brief

detail

interfaces

] [

vrf-name

] [

output-modifiers

]

Syntax Description

Defaults

When no keywords or arguments are specified, the command shows concise information about all
configured VRFs.

Command Modes

Privileged EXEC

Command History

Usage Guidelines

Use this command to display information about VRFs. Two levels of detail are available:

•

The

brief

keyword (or no keyword) displays concise information.

•

The

detail

keyword displays all information.

To display information about all interfaces bound to a particular VRF, or to any VRF, use the

interfaces

keyword. To display information about VPN IDs assigned to a PE router, use the

keyword.

Examples

The following example displays information about all the VRFs configured on the router, including the
downstream VRF for each associated VAI. The lines that are highlighted (for documentation purposes
only) indicate the downstream VRF.

Router#

show ip vrf

Name Default RD Interface

D 2:0 Loopback2

Virtual-Access3 [D]

brief

(Optional) Displays concise information on the VRFs and associated
interfaces.

detail

(Optional) Displays detailed information on the VRFs and associated
interfaces.

interfaces

(Optional) Displays detailed information about all interfaces bound
to a particular VRF or any VRF.

(Optional) Displays the VPN IDs that are configured in a PE router
for different VPNs.

vrf-name

(Optional) Name assigned to a VRF.

output-modifiers

(Optional) For a list of associated keywords and arguments, use
context-sensitive help.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды