Cisco 901 Скачать руководство пользователя страница 195

Страница: 195 / 218

1-181

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show policy-map interface

Related Commands

Command

Description

class-map

Creates a class map to be used for matching packets to a specified class.

police

Configures traffic policing.

police (percent)

Configures traffic policing on the basis of a percentage of bandwidth
available on an interface.

police (two rates)

Configures traffic policing using two rates, the CIR and the PIR.

policy-map

Creates or modifies a policy map that can be attached to one or more
interfaces to specify a service policy.

priority

Specifies that low-latency behavior must be given to a traffic class and
configures multiple priority queues.

shape (percent)

Specifies average or peak rate traffic shaping on the basis of a percentage
of bandwidth available on an interface.

show class-map

Display all class maps and their matching criteria.

show interfaces

Displays statistics for all interfaces configured on a router or access server.

show policy-map

Displays the configuration of all classes for a specified service policy map
or all classes for all existing policy maps.

show policy-map class

Displays the configuration for the specified class of the specified policy
map.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды