Cisco 901 Скачать руководство пользователя страница 13

Страница: 13 / 218

1-5

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 Using Command-Line Interface

Using the No and Default Forms of Commands

Almost every configuration command has a

form. In general, enter the

form to disable a function.

Use the command without the keyword

to reenable a disabled function or to enable a function that is

disabled by default. For example, IP routing is enabled by default. To disable IP routing, specify the

no ip routing

command and specify

ip routing

to reenable it. This publication provides the complete

syntax for the configuration commands and describes what the

form of a command does.

Configuration commands can have a

default

form. The

default

form of a command returns the command

setting to its default. Most commands are disabled by default, so the

default

form is the same as the

form. However, some commands are enabled by default and have arguments that are set to certain default
values. In these cases, the

default

form of the command enables the command and sets arguments to

their default values. This publication

describes what the

default

form of a command does if the

command is not the same as the

form.

Saving Configuration Changes

To save your configuration changes to your startup configuration so that they will not be lost if there is
a system reload or power outage, enter the following command:

Router#

copy system:running-config nvram:startup-config

Building configuration...

It might take a minute or two to save the configuration. After the configuration has been saved, the
following output appears:

[OK]

Router#

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды