Cisco 901 Скачать руководство пользователя страница 183

Страница: 183 / 218

1-169

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show platform ptp state

To display the status of ptp protocol on the Cisco ASR 901 router, use the

show platform ptp state

command.

show platform ptp state

Syntax Description

This command has no arguments.

Command Modes

Privileged EXEC

Command History

Examples

The following example shows sample output for

show platform ptp state

comamnd:

Router#

show platform ptp state

flag = 2

FLL State : 2 (Fast Loop)

FLL Status Duration : 7049 (sec)

Forward Flow Weight : 0.0

Forward Flow Transient-Free : 900 (900 sec Window)

Forward Flow Transient-Free : 3600 (3600 sec Window)

Forward Flow Transactions Used: 23.0 (%)

Forward Flow Oper. Min TDEV : 4254.0 (nsec)

Forward Mafie : 38.0

Forward Flow Min Cluster Width: 7550.0 (nsec)

Forward Flow Mode Width : 21400.0 (nsec)

Reverse Flow Weight : 100.0

Reverse Flow Transient-Free : 900 (900 sec Window)

Reverse Flow Transient-Free : 3600 (3600 sec Window)

Reverse Flow Transactions Used: 200.0 (%)

Reverse Flow Oper. Min TDEV : 487.0 (nsec)

Reverse Mafie : 36.0

Reverse Flow Min Cluster Width: 225.0 (nsec)

Reverse Flow Mode Width : 450.0 (nsec)

Frequency Correction : 257.0 (ppb)

Phase Correction : 0.0 (ppb)

Output TDEV Estimate : 1057.0 (nsec)

Output MDEV Estimate : 1.0 (ppb)

Residual Phase Error : 0.0 (nsec)

Min. Roundtrip Delay : 45.0 (nsec)

Sync Packet Rate : 65 (pkts/sec)

Delay Packet Rate : 65 (pkts/sec)

Forward IPDV % Below Threshold: 0.0

Forward Maximum IPDV : 0.0 (usec)

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды

Cisco 901, Справочник по командам

Результаты поиска

Содержание 901

Отзывы:

Похожие инструкции для 901

Бренды по названию

Популярные бренды