manualshive.com logo in svg

Cisco 901, Справочник по командам

У нас есть бесплатное руководство по продукту Oklahoma Sound 901! Скачайте его с manualshive.com и узнайте как максимально эффективно использовать вашу аудиосистему. В нашем Product Handbook вы найдете все необходимые инструкции и советы для комфортного использования продукта.

Поделиться
Скачать
background image

1-118

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  router isis

router isis

To enable the Intermediate System-to-Intermediate System (IS-IS) routing protocol and to specify an 
IS-IS process, use the 

router isis

 command in global configuration mode. To disable IS-IS routing, use 

the 

no 

form of this command.

router isis 

area-tag

no router isis 

area-tag

Syntax Description

Defaults

This command is disabled by default.

Command Modes

Global configuration

Command History

Usage Guidelines

This command is used to enable routing for an area. An appropriate network entity title (NET) must be 
configured to specify the area address of the area and system ID of the router. Routing must be enabled 
on one or more interfaces before adjacencies may be established and dynamic routing is possible.

If you have IS-IS running and at least one International Standards Organization Interior Gateway 
Routing Protocol (ISO-IGRP) process, the IS-IS process and the ISO-IGRP process cannot both be 
configured without an area tag. The null tag can be used by only one process. If you run ISO-IGRP and 
IS-IS, a null tag can be used for IS-IS, but not for ISO-IGRP at the same time. However, each area in an 
IS-IS multiarea configuration should have a nonnull area tag to facilitate identification of the area.

You can configure only one IS-IS routing process to perform Level 2 (interarea) routing. You can 
configure this process to perform Level 1 (intra-area) routing at the same time. You can configure up to 
29 additional processes as Level 1-only processes. If Level 2 routing is configured on any process, all 
additional processes are automatically configured as Level 1.

An interface cannot be part of more than one area, except in the case where the associated routing 
process is performing both Level 1 and Level 2 routing. On media such as WAN media where 
subinterfaces are supported, different subinterfaces could be configured for different areas. 

If Level 2 routing is not desired for a given area, use the 

is-type

 command to remove Level 2. Level 2 

routing can then be enabled on some other router instance.

area-tag

Meaningful name for a routing process. If it is not specified, a null 
tag is assumed and the process is referenced with a null tag. This 
name must be unique among all IP or Connectionless Network 
Service (CLNS) router processes for a given router.

Required for multiarea IS-IS configuration. Optional for 
conventional IS-IS configuration. 

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Содержание 901



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 901

Aastra CNX Product Brief preview
CNX
Бренд: Aastra Страницы: 2
QNAP QMiroPlus-201W Quick Installation Manual preview
QMiroPlus-201W
Бренд: QNAP Страницы: 20
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Бренд: Supero Страницы: 112
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Бренд: Enterasys Страницы: 58
Lantronix WP2002000-01 User Manual preview
WP2002000-01
Бренд: Lantronix Страницы: 75
ADTRAN TRACER 5045 Manual preview
TRACER 5045
Бренд: ADTRAN Страницы: 9
ADC HiGain H4TU-R-402 List 5A Quick Installation preview
HiGain H4TU-R-402 List 5A
Бренд: ADC Страницы: 7
TRENDnet TW100-W2plus Specifications preview
TW100-W2plus
Бренд: TRENDnet Страницы: 2
TRENDnet TE100-S2424V Specifications preview
TE100-S2424V
Бренд: TRENDnet Страницы: 2
Belkin F9K1002V1 User Manual preview
F9K1002V1
Бренд: Belkin Страницы: 42
AIC HA201-AP User Manual preview
HA201-AP
Бренд: AIC Страницы: 64
EtherWAN EX17016 Installation Manual preview
EX17016
Бренд: EtherWAN Страницы: 2
Westermo RedFox User Manual preview
RedFox
Бренд: Westermo Страницы: 20
Bolt IoT PLATFORM Quick Start Manual preview
IoT PLATFORM
Бренд: Bolt Страницы: 18
TRENDnet TEW-630APB - Wireless Access Point User Manual preview
TEW-630APB - Wireless Access Point
Бренд: TRENDnet Страницы: 56
Tripp Lite N316-10M Specification Sheet preview
N316-10M
Бренд: Tripp Lite Страницы: 2
Billion M500 User Manual preview
M500
Бренд: Billion Страницы: 181

Бренды по названию

Популярные бренды

Загрузить еще бренды