Chopin Mixolab 2 Скачать руководство пользователя страница 12

Страница: 12 / 134

Maintenance manual

09/2016

Mixolab 2

Chapter 1 Use and maintenance: re-

minders and further information

Note:

For passwords, see the procedures in this manual.

❏

History

The "Mixolab Chopin" software includes a history of settings and
errors that can be used for maintenance of the Mixolab.

To access it, click "History" then "History".

❏

Software updates

An "Update" menu transfers a new version of the embedded
software. This function is reserved for duly authorized persons -

see

Operation 12-1 "Updating the Mixolab software" page 89

Dough
temperature
sensor

Mixing motor

speed setpoint

Actual mixing

motor speed

Access to settings

(password-

protected)

Cooling solenoid
valve

Torque sensor

Cover lock

Mixing bowl
temperature
setpoint

Actual
temperature of
mixing bowl

Mixing bowl lock

Water tank
temperature
setpoint

Actual
temperature of the
water tank

Water dosing syringe

Quantity of water in ml

Deactivation of the
temperature adjustment
factor (maintenance mode)

Activation of

integral calibration

for tests

Содержание Mixolab 2







































































































































Результаты поиска

Содержание Mixolab 2

Отзывы:

Бренды по названию

Популярные бренды

Chopin Mixolab 2, Руководство по обслуживанию

Результаты поиска

Содержание Mixolab 2

Отзывы:

Бренды по названию

Популярные бренды