Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 64

Страница: 64 / 82

5. Do the following to remove the filter housing:

a. Slide the filter wrench onto the filter housing with the

handle pointing to the right.

b. Pull handle toward you to loosen the housing; then

unscrew the housing by hand. Figure 7.11

Hold a container below the housing to catch any spills.

6. Clean the filter housing using soap and water and then

rinse thoroughly.

7. Inspect the O-ring for twists, wear, or damage. If necessary,

replace the O-ring. Figure 7.12

8. Apply an NSF-approved silicone lubricant to the

housing O-ring to aid assembly and sealing.

9. Insert the new filter into the housing.
10. Re-attach the filter housing. FIgure 7.13

Hand tighten only. Do not use the filter wrench to tighten
the housing.

11. Open the main (external) water supply valve.

Check the filter housing carefully for leaks after opening the
water supply valve.

12. Purge air from the on-board .2 micron water filter housing

(for instructions, see

Periodic Maintenance

13. Record the date of change in the log.

Figure 7.11

- Remove Filter Housing

Figure 7.12

- Inspect and Lubricate O-ring

Figure 7.13

- Replace Filter Housing by Hand

Содержание MEDIVATOR DSD EDGE



















































































Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды

Cantel Medical MEDIVATOR DSD EDGE, Руководство пользователя

Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды