Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 25

Страница: 25 / 82

REPROCESSING CYCLE

•

If monitored sensors are not satisfied during startup, the cycle is halted until the
issue is resolved or cycle is cancelled.

•

Automated Leak Tester (Optional).

If enabled, a 40 second leak test is

performed before starting the Flush phase.

•

Fresh water is flushed through scope channels and basin.

•

Detergent (Optional).

If programmed, detergent is injected into the

channels prior to the fresh water flush.

•

Incoming water temperature is monitored to ensure water temperature is reaching
proper range for disinfection.

•

Concludes by purging scope channels with air and emptying the basin of water.

•

An additional one or two soak segments can be added to the Flush phase.

•

No detergent is injected during additional soak segments.

•

Endoscope channels are flushed with disinfectant.

•

Basin is filled with disinfectant solution and endoscope is soaked for the 5 minute
disinfectant soak time.

•

Concludes by draining disinfectant from the basin.

•

Basin is partially filled with fresh water as scope channels are flushed with fresh
water. Partially filled basin is then drained.

•

Basin is completely filled with fresh water as scope channels are flushed with
fresh water. Basin is then drained while the channels are purged with fresh water.

•

Concludes by purging scope channels with air.

STARTUP

FLUSH

WASH

(Optional)

DISINFECT

RINSE 1

Содержание MEDIVATOR DSD EDGE



















































































Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды

Cantel Medical MEDIVATOR DSD EDGE, Руководство пользователя

Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды