Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 82

background image

|

43

CONTINUE A CYCLE AFTER AN OPERATOR INTERRUPTION

1. On the control panel, verify the correct station is selected. If necessary, press

STATION SELECT

to choose

the station (A or B).

2. Press

START

. The cycle proceeds as normal.

TERMINATE A CYCLE AFTER AN INTERRUPTION

1. On the control panel, verify the correct station is selected. If necessary, press

STATION SELECT

to choose

the station (A or B).

2. Press

CANCEL

.

3. Press

ENTER

.

“Aborted” displays on the screen. The cycle has been successfully terminated. When a cycle is terminated,
the reprocessor fails to a safe mode and the disinfection cycle must be re-run for the endoscope.
An endoscope must not be used until the entire disinfection process has successfully completed.

SHUTDOWN THE REPROCESSOR

The reprocessor must be properly shut down at the end of each day.

1. Close the main (external) water supply valve.

2. Sanitize the reprocessor upper basins and basin lids

with an EPA-registered sanitizer, such as properly diluted
ACTRIL™ Cold Sterilant. Follow the sanitizer manufacturer’s
recommendations for proper use.

Figure 5.5

- Close External Water

Supply Valve

Warning!

Avoid possible chemical burns. Always wear personal protective

equipment (gloves, goggles) when handling sanitizer.

«
...
41
42
43
44
45
...
»

Содержание MEDIVATOR DSD EDGE



















































































Отзывы:

Нет отзывов

Похожие инструкции для MEDIVATOR DSD EDGE

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: QBC Diagnostics Страницы: 65

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды