Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 30

Страница: 30 / 82

CHECK DISINFECTANT CONTAINERS

Disinfectant is supplied in two separate 5-liter containers. Part A is the Peracetic Acid component, Part B is the
buffer. Both containers fit into the disinfectant drawer located on the left-hand side of the reprocessor.

Warning!

Avoid possible chemical burns. Always wear personal protective

equipment (gloves, goggles) when handling disinfectant.

Warning!

Avoid possible slip injuries. Clean up any spills immediately.

Note:

On the control panel LCD screen, error message “Low Part A, Low Part B” displays if

a disinfectant container is low and needs to be replaced. Do not manually determine whether
disinfectant levels are low.

Note:

If Part A or Part B need to be replaced, replace both containers. Always replace both

containers at the same time.

Note:

Part A Uptake Tube is fitted with the BLUE cap. Part B Uptake Tube is fitted with the

WHITE cap.

Note:

Ensure that Part A and B caps are securely screwed onto containers.

1. Open the reprocessor doors and slide the

disinfectant drawer fully out.

Figure 4.4.

- Disinfectant Drawer

Содержание MEDIVATOR DSD EDGE



















































































Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды

Cantel Medical MEDIVATOR DSD EDGE, Руководство пользователя

Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды