Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 33

Страница: 33 / 82

1. On the control panel, press

SETUP

2. Type

on the keypad, then press

ENTER

3. “Water temp test?” displays on the LCD screen.

Press

ENTER

to initiate water flow.

4. As water flows into the basin, verify the dynamic

water pressure.

Dynamic water pressure at the inlet to the
reprocessor must be 35-40 psi (2.4-2.75 BAR).

Figure 4.7

- Verify Dynamic Water Pressure

5. As water flows into the basin, verify the incoming

water temperature readings on the control panel
LCD screen. The incoming water temperature for
each basin displays in the second column.

Incoming water temperature should be
approximately 35°C (± 2°C).

Figure 4.8

- Display Water Temperature

6. Once the water pressure and temperature have been verified, press

STOP

Water continues to flow until manually stopped or if the temperature reaches 40°C.

7. “Basin drained?” displays on the screen. Once the basin is completely drained, press

STOP

to close the

drain valve.

Note:

The basin drain valves close automatically after 250 seconds.

Содержание MEDIVATOR DSD EDGE



















































































Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды

Cantel Medical MEDIVATOR DSD EDGE, Руководство пользователя

Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды