Cantel Medical MEDIVATOR DSD EDGE Скачать руководство пользователя страница 21

Страница: 21 / 82

LCD SCREEN

The LCD screen displays system messages and prompts that help guide the operator.

Note:

See Appendix for a list of user prompts and error messages.

Figure 2.8

- LCD Screen

Station and Program:

The current operating
program for each station
displays in the bottom row.

User Prompts:

Messages and queries
display in the top row.
“A:” represents station A,
“B:” represents station B

Program status:

The status of the program
displays to the right of the
program number:

No indicator

Indicates station is idle

+ and * (alternating)

Indicates station is stopped

R and r (alternating)

Indicates station is resetting

: and | (alternating)

Indicates station is running

Date and Time:

The current time,
day of week and date
display on the right
side of the screen.

Содержание MEDIVATOR DSD EDGE



















































































Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды

Cantel Medical MEDIVATOR DSD EDGE, Руководство пользователя

Результаты поиска

Содержание MEDIVATOR DSD EDGE

Отзывы:

Похожие инструкции для MEDIVATOR DSD EDGE

Бренды по названию

Популярные бренды