Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 933 | Manualshive

Страница: 933 / 1505

background image

Brocade Network Advisor SAN User Manual

885

53-1002696-01

FC troubleshooting

28

Confirming Fabric Device Sharing

NOTE

Fabric device sharing is only available with Trial or Licensed version.

NOTE

Fabric device sharing is only available on pure Fabric OS fabrics.

To confirm that two or more fabrics have been configured to share devices, complete the following
steps.

1. Select Configure > FC Troubleshooting > Fabric Device Sharing.

The Fabric Device Sharing Diagnosis dialog box displays.

2. Select the fabrics (two or more) for which you want to confirm device sharing from the Available

Fabrics table.

3. Click the right arrow button.

4. Click OK.

The following checks are performed on the selected fabrics:

•

Are the selected fabrics configured with an FC Router?

•

Are the selected fabrics connected to the same backbone fabric?

•

Is sharing of devices between backbone and edge fabric supported?

The Fabric Device Sharing Diagnosis Results dialog box displays with the details of the fabrics
selected for diagnosis, the details of the tests performed, the results of the test, as well as
short description of the test results.

5. Click Close on the Fabric Device Sharing Diagnosis Results dialog box.

6. Click Cancel on the Fabric Device Sharing Diagnosis dialog box.

Troubleshooting port diagnostics

This feature allows you to run a diagnostic port test and a link traffic test on the selected ports.

Port diagnostics requirements

•

Only supported on devices with 10 Gbps-capable D-ports or E-ports running Fabric OS 7.0 or
later. The source and destinationports must be the same.

•

Only supported on devices with 16 Gbps-capable E-ports running Fabric OS 7.0 or later.

•

Only supported on devices with 16 Gbps-capable F-ports, ICL-ports, and AG N-ports running
Fabric OS 7.1 or later.

•

Both the source and destination ports must be managed by the Management application.

ATTENTION

The Management application changes the port type for all selected ports and associated attached
ports to a D port for the duration of the test. This may cause the fabric to segment. When the test is
complete, the Management application changes the port type back to an E port.

«
...
931
932
933
934
935
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Advisor 12.0.0

Бренд: Canon Страницы: 82

Powershot A650 IS

Бренд: Canon Страницы: 49

4116 - SCX B/W Laser

Бренд: Samsung Страницы: 14

2252W - Printer - B/W

Бренд: Samsung Страницы: 10

Бренд: Yamaha Страницы: 89

Бренд: TAA Страницы: 28

Бренд: AMD Страницы: 120

GHOST IMAGING FOUNDATION 7.1

Бренд: Symantec Страницы: 189

LINUX ENTERPRISE DESKTOP 11 - KDE

Бренд: Novell Страницы: 102

Controller Mode

Бренд: Sony Ericsson Страницы: 10

8.5 EMAIL SERVER EDITION - V 85.4

Бренд: AVG Страницы: 52

Бренд: Qlogic Страницы: 180

Бренд: TruCluster Страницы: 88

Бренд: RedMoon Music Страницы: 74

DVD MOVIEFACTORY 5

Бренд: Ulead Страницы: 72

Бренд: Promise Technology Страницы: 84

Бренд: Vonamic Страницы: 31

Бренд: Draytek Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды