Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 850 | Manualshive

Страница: 850 / 1505

background image

802

Brocade Network Advisor SAN User Manual

53-1002696-01

Fabric Bining overview

23

2. In the Fabric List table, click the Enable/Disable check box for fabrics for which you want to

configure fabric binding.

For instructions on adding and removing switches from the membership list, refer to

“Adding

switches to the fabric binding membership list”

on page 803 and

“Removing switches from

fabric binding membership”

on page 804.

3. Click OK on the Fabric Binding dialog box.

The Fabric Binding Status dialog box displays with the following information:

•

Fabric Name — Displays the enabled fabric name selected for fabric binding.

•

Applying Fabric Binding Changes for selected fabric message — Displays the status of the
fabric binding changes.

•

Setting SCC Policy message — The Switch Connection Control (SCC) policy prevents
unauthorized devices from joining a fabric.

•

Setting FWCP Policy message — Fabric-wide consistency is necessary for FICON switch
binding.

•

List of possible reasons that could cause Fabric Binding failure message — Refer to the

Fabric OS Administrator’s Guide

for detailed information.

Disabling fabric binding

Fabric Binding cannot be disabled while High Integrity Fabric is active if the switch is offline. This
disables fabric binding and High Integrity Fabric on the switch, but not the rest of the fabric.
Disabled switches segment from the fabric.

NOTE

Fabric Binding is only supported on Fabric OS 5.2 or later.

1. Select Configure > Fabric Binding.

The Fabric Binding dialog box displays (

Figure 363

).

2. In the Fabric List table, clear the Enable/Disable check box for fabrics for which you want to

disable fabric binding.

3. Click OK on the Fabric Binding dialog box.

The Fabric Binding Status dialog box displays with the following information:

•

Fabric Name — Displays the enabled fabric name selected for fabric binding.

•

Applying Fabric Binding Changes for selected fabric message — Displays the status of the
fabric binding changes.

•

Setting SCC Policy message — The Switch Connection Control (SCC) policy prevents
unauthorized devices from joining a fabric.

•

Setting FWCP Policy message — Fabric-wide consistency is necessary for FICON switch
binding.

•

List of possible reasons that could cause Fabric Binding failure message — Refer to the
Fabric OS Administrator’s Guide for detailed information.

«
...
848
849
850
851
852
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Advisor 12.0.0

ANTI-VIRUS 5.0 - FOR SAMBA SERVERS

Бренд: KAPERSKY Страницы: 84

ADMINISTRATION KIT 6.0

Бренд: KAPERSKY Страницы: 37

ADMINISTRATION KIT 6.0

Бренд: KAPERSKY Страницы: 109

TRANSCEND EM/NT 6.3

Бренд: 3Com Страницы: 39

Бренд: Campbell Страницы: 133

Бренд: ShoreTel Страницы: 25

SimNow Simulator 4.4.5

Бренд: AMD Страницы: 269

WiFi-Doc Client for iOS

Бренд: Mitsubishi Страницы: 10

Бренд: MacroSystem Digital Video Страницы: 28

13101332 - Photoshop - Mac

Бренд: Adobe Страницы: 549

Бренд: DataCard Страницы: 2

Venture IP Telephone System

Бренд: Aastra Страницы: 12

Бренд: Emagic Страницы: 256

Бренд: RedMoon Music Страницы: 74

READIRIS 12 PRO

Бренд: IRIS Страницы: 6

2521131 - Intel Wasp Motherboard

Бренд: Intel Страницы: 1

AURORA EDIT - INSTALLATION V7.1

Бренд: GRASS VALLEY Страницы: 152

Бренд: Autodesk Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды