Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 563 | Manualshive

Страница: 563 / 1505

background image

Brocade Network Advisor SAN User Manual

515

53-1002696-01

Configuring Virtual Fabrics

19

3. Set up logical switches in each physical chassis.

a. Create logical switches in each physical chassis and assign ports to them. Make sure the

logical switches are configured to allow XISL use.

Refer to

“Creating a logical switch or base switch”

on page 516 for instructions.

b. Disable all of the logical switches in each physical chassis.

Right-click each logical switch in the Connectivity Map or Product List and select
Enable/Disable > Disable.

c. Physically connect devices and ISLs to the ports on the logical switches.

You can connect ISLs from one logical switch to another logical switch in a different
physical chassis only if the two logical switches have the same FID (and are thus in the
same logical fabric). Traffic between these logical switches can travel over either this ISL or
the XISL in the base fabric. The physical ISL path is favored over the XISL path because it
has a lower cost.

d. Enable all logical switches in each chassis.

Right-click each logical switch in the Connectivity Map or Product List and select
Enable/Disable > Enable.

The logical fabric is formed.

Enabling Virtual Fabrics

For a list of platforms that are Virtual Fabrics-capable, refer to

“Virtual Fabrics requirements”

on

page 512.

ATTENTION

If the physical chassis is participating in a fabric, the affected fabric will be disrupted.

1. Select the physical chassis in the topology and select Configure > Virtual Fabric > Enable.

Alternatively, you can right-click the physical chassis and select Enable Virtual Fabric.

2. Read the warning message and click OK.

Disabling Virtual Fabrics

ATTENTION

Disabling Virtual Fabrics deletes all logical switches, returns port management to the physical
chassis, and reboots the physical chassis. If these logical switches are participating in a fabric, all
affected fabrics will be disrupted.

1. Select the physical chassis in the Chassis Group and select Configure > Virtual Fabric >

Disable.

Alternatively, you can right-click the physical chassis in the Chassis Group and select Disable
Virtual Fabric.

2. Read the warning message and click OK.

«
...
561
562
563
564
565
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Advisor 12.0.0

Бренд: Acer Страницы: 4

Бренд: SanDisk Страницы: 11

Бренд: National Instruments Страницы: 63

APPLICATION STACK 2.0 RELEASE

Бренд: Red Hat Страницы: 26

NETWORK SATELLITE SERVER 4.0

Бренд: Red Hat Страницы: 80

NETWORK - USER REFERENCE GUIDE 3.1

Бренд: Red Hat Страницы: 78

NETWORK SATELLITE 5.1.0 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 300

Бренд: Acroprint Страницы: 2

Active Management Technology v4.0

Бренд: Intel Страницы: 143

AUTOCAD ELECTRICAL 2005

Бренд: Autodesk Страницы: 88

Бренд: Bay Networks Страницы: 130

Бренд: TerraTec Страницы: 20

Terminal Emulation TN5250

Бренд: IBM Страницы: 51

Бренд: Tandem Страницы: 312

Lazett Combo SCX-4116

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 30

EOS DIGITAL REBEL XT/350D DIGITAL

Бренд: Canon Страницы: 42

FLASH MX 2004 - FLASH LITE AUTHORING GUIDELINES FOR THE I-MODE SERVICE

Бренд: MACROMEDIA Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды