Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 432

Страница: 432 / 1505

384

Brocade Network Advisor SAN User Manual

53-1002696-01

Port Auto Disable

4. Select the device on which you want to enable PAD on all ports.

5. Click Configure.

The Configure Port Auto Disable dialog box displays.

6. Select one or more of the following event types:

•

Port Auto Disable

•

Loss Of Sync — Requires devices running Fabric OS 7.0 or later.

•

Loss Of Signal — Requires devices running Fabric OS 7.0 or later.

•

OLS (Offline Primitive Sequence) — Requires devices running Fabric OS 7.0 or later.

•

NOS (Not Operational Primitive Sequence) — Requires devices running Fabric OS 7.0 or
later.

•

LIP (Loop Initialization Primitive Sequence) — Requires devices running Fabric OS 7.0 or
later.

7. Click OK on the Configure Port Auto Disable dialog box.

8. Click OK on the Port Auto Disable dialog box.

Disabling port auto disable on individual ports

NOTE

The device must be running Fabric OS 6.3 or later.

To disable port auto disable on individual ports, complete the following steps.

1. Select Configure > Port Auto Disable.

The Port Auto Disable dialog box displays.

2. Select the fabric on which you want to disable port auto disable (PAD) from the Fabric list.

3. Choose one of the following options from the Show list to filter the port list:

•

All Ports (default) — Displays all ports in the fabric.

•

Enabled PAD — Displays only ports where PAD is enabled.

4. Select the ports on which you want to disable PAD.

5. Click Configure.

The Configure Port Auto Disable dialog box displays.

6. Clear any of the following selected event types.

•

Port Auto Disable

•

Loss Of Sync — Requires devices running Fabric OS 7.0 or later.

•

Loss Of Signal — Requires devices running Fabric OS 7.0 or later.

•

OLS (Offline Primitive Sequence) — Requires devices running Fabric OS 7.0 or later.

•

NOS (Not Operational Primitive Sequence) — Requires devices running Fabric OS 7.0 or
later.

•

LIP (Loop Initialization Primitive Sequence) — Requires devices running Fabric OS 7.0 or
later.

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды

Brocade Communications Systems Network Advisor 12.0.0, Руководство пользователя

Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды