Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 1426

Страница: 1426 / 1505

1378

Brocade Network Advisor SAN User Manual

53-1002696-01

Views

select

FCIP_TUNNEL.ID,

FCIP_TUNNEL.TUNNEL_ID,

FCIP_TUNNEL.VLAN_TAG,

FCIP_TUNNEL.SOURCE_IP,

FCIP_TUNNEL.DEST_IP,

FCIP_TUNNEL.LOCAL_WWN,

FCIP_TUNNEL.REMOTE_WWN_RESTRICT,

FCIP_TUNNEL.COMMUNICATION_RATE,

FCIP_TUNNEL.MIN_RETRANSMIT_TIME,

FCIP_TUNNEL.SELECTIVE_ACK_ENABLED,

FCIP_TUNNEL.KEEP_ALIVE_TIMEOUT,

FCIP_TUNNEL.MAX_RETRANSMISSION,

FCIP_TUNNEL.WAN_TOV_ENABLED,

FCIP_TUNNEL.TUNNEL_STATUS,

FCIP_TUNNEL.DESCRIPTION,

FCIP_TUNNEL.FICON_TRB_ID_ENABLED,

FCIP_TUNNEL.FICON_TT_EMUL_ENABLED,

FCIP_TUNNEL.FICON_DLA_EMUL_ENABLED,

FCIP_TUNNEL.FICON_TAPE_WRITE_MAX_PIPE,

FCIP_TUNNEL.FICON_TAPE_READ_MAX_PIPE,

FCIP_TUNNEL.FICON_TAPE_WRITE_MAX_OPS,

FCIP_TUNNEL.FICON_TAPE_READ_MAX_OPS,

FCIP_TUNNEL.FICON_TAPE_WRITE_TIMER,

FCIP_TUNNEL.FICON_TAPE_MAX_WRITE_CHAIN,

FCIP_TUNNEL.FICON_OXID_BASE,

FCIP_TUNNEL.FICON_XRC_EMULATION_ENABLED,

FCIP_TUNNEL.FICON_TW_EMUL_ENABLED,

FCIP_TUNNEL.FICON_TR_EMUL_ENABLED,

FCIP_TUNNEL.FICON_DEBUG_FLAGS,

FCIP_TUNNEL.REMOTE_WWN,

FCIP_TUNNEL.CDC,

FCIP_TUNNEL.ADMIN_STATUS,

FCIP_TUNNEL.CONTROL_L2_COS,

FCIP_TUNNEL.DSCP_CONTROL,

FCIP_TUNNEL.TRUNKING_ALGORITHM,

FCIP_TUNNEL.EXTENDED_TUNNEL,

FCIP_TUNNEL.VIRTUAL_SWITCH_ID,

FCIP_TUNNEL.CIRCUIT_COUNT,

FCIP_TUNNEL.MISMATCHED_CONFIG_DETAILS,

FCIP_TUNNEL.SLOT_NUMBER,

FCIP_TUNNEL.FICON_ENABLED,

FCIP_TUNNEL.TPERF_ENABLED,

FCIP_TUNNEL.AUTH_KEY,

FCIP_TUNNEL.CONNECTED_COUNT,

FCIP_TUNNEL.TUNNEL_STATUS_STRING,

FCIP_TUNNEL.COMPRESSION_MODE,

FCIP_TUNNEL.TURBO_WRITE_ENABLED,

FCIP_TUNNEL.TAPE_ACCELERATION_ENABLED,

FCIP_TUNNEL.IPSEC_ENABLED,

FCIP_TUNNEL.PRESHARED_KEY,

FCIP_TUNNEL.QOS_HIGH,

FCIP_TUNNEL.QOS_MEDIUM,

FCIP_TUNNEL.QOS_LOW,

FCIP_TUNNEL.BACKWARD_COMPATIBLE,

FCIP_TUNNEL.FICON_TERADATA_READ_ENABLED,

FCIP_TUNNEL.FICON_TERADATA_WRITE_ENABLED,

PORT.WWN as VIRTUAL_PORT_WWN,

PORT.REMOTE_PORT_WWN as REMOTE_PORT_WWN,

PORT.REMOTE_NODE_WWN as REMOTE_NODE_WWN,

«
...
1424
1425
1426
1427
1428
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды

Brocade Communications Systems Network Advisor 12.0.0, Руководство пользователя

Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды