Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 574

Страница: 574 / 1505

526

Brocade Network Advisor SAN User Manual

53-1002696-01

Encryption Center features

•

Redirection zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682

•

Disk device decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682

•

Rekeying all disk LUNs manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685

•

Thin provision LUNs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690

•

Viewing time left for auto rekey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691

•

Viewing and editing switch encryption properties. . . . . . . . . . . . . . . . . . . . 692

•

Viewing and editing encryption group properties . . . . . . . . . . . . . . . . . . . . 696

•

Encryption-related acronyms in log messages . . . . . . . . . . . . . . . . . . . . . . 712

Encryption Center features

The Encryption Center dialog box is the single launching point for all encryption-related
configuration in the Management application (

Figure 185

). It also provides a table that shows the

general status of all encryption-related hardware and functions at a glance. To open the dialog box,
select Configure > Encryption.

FIGURE 185

Encryption Center dialog box

Beginning with Fabric OS 6.4, the Encryption Center is dynamically updated to reflect the latest
changes based on any of the following events:

•

Encryption group creation or deletion.

•

A change in encryption group status or encryption engine status

•

Addition or removal of an encryption group member or encryption engine

If you are using the Encryption Center for the first time, please read the following topics before you
begin to perform encryption operations:

•

“Encryption user privileges”

on page 527 describes the Role-based Access Control privileges

that are specific to encryption.

•

“Smart card usage”

on page 528 and the topics that follow describe the options available for

the use of Smart Cards for user authentication, system access control, and storing backup
copies of data encryption master keys.

•

“Network connections”

on page 539 describes the network connections that must be in place

to enable encryption.

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды

Brocade Communications Systems Network Advisor 12.0.0, Руководство пользователя

Результаты поиска

Содержание Network Advisor 12.0.0

Отзывы:

Похожие инструкции для Network Advisor 12.0.0

Бренды по названию

Популярные бренды