Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 890 | Manualshive

Страница: 890 / 1505

background image

842

Brocade Network Advisor SAN User Manual

53-1002696-01

Cascaded FICON fabric

25

5. Select to enable port-based, exchange-based, or device-based routing on switches.

If you select Port-Based Routing, enables port-based routing on 4 Gbps platform switches.

If you select Exchange-Based Routing, enables exchange-based routing for the fabric if all
switches are 8 Gbps or greater platforms running Fabric OS 6.4 or later. If these requirements
are not met, an error message displays.

If you select Device-Based Routing, enables device-based routing for the fabric if all switches in
the fabric are 8 Gbps or greater platforms running Fabric OS 7.1 or later. If these requirements
are not met, an error message displays.

NOTE

Either exchange-, port-, or device-based routing are enabled on all switches of selected fabric.
You cannot enable a mixed routing policy.

6. Click OK if you want to proceed.

7. A warning message displays explaining that SCC and DCC policies will be created and activated

on the fabric. Click Yes to continue.

If configuration is successful, a confirmation message displays.

If FMS Mode was selected, each switch is checked for a CUP license. Any switches that do not
have a CUP license are listed, with a reminder that a CUP license is necessary to communicate
with the S/B FICON Management Server.

NOTE

FMS mode cannot be enabled on switches running Fabric OS 7.0 and later unless the switches
have an active CUP license.

Enabling DLS

Consider the following when enable Dynamic Load Sharing (DLS) in

step 4

:

•

DLS requires DLS support on the switch. Lossless DLS requires Lossless DLS support on the
switch.

•

Enabling DLS will enable IOD without lossless DLS on all other switches, enable DLS on
switches that support DLS, and disable DLS on all other switches.

•

DLS is only supported on the 40-port, 8 Gbps FC Switch, 80-port, 8 Gbps FC Switch, 512-port
Backbone Chassis, and 4-slot Backbone Chassis.

•

Enabling DLS may result in dropped frames when paths fail over. It is recommended that you
set the preferred IOD Delay Time to minimize frame drops.

•

To enable DLS, all switches in the fabric must be 8 Gbps or faster and running Fabric OS 6.4 or
later.

«
...
888
889
890
891
892
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Advisor 12.0.0

Бренд: Native Instruments Страницы: 74

Бренд: TAA Страницы: 28

Mobile Anti-Virus 60 Series

Бренд: F-SECURE Страницы: 90

ATV-TURBO - WINDOWS 98

Бренд: OCZ Страницы: 5

JBoss Developer Studio 3.0

Бренд: Red Hat Страницы: 78

Advanced Calculator 2.2

Бренд: CDML Страницы: 48

Telephony Modem Simulator

Бренд: Intrinsyc Страницы: 2

Бренд: VDO Страницы: 8

BD DISCRECORDER

Бренд: Ulead Страницы: 18

Бренд: nordic edge Страницы: 49

Бренд: ViewSonic Страницы: 2

ALTIRIS DEPLOYMENT SOLUTION 7.1 - FOR DELL SERVERS V1.0

Бренд: Symantec Страницы: 47

Бренд: Gallo Страницы: 9

Бренд: Intel Страницы: 19

Бренд: FieldServer Страницы: 15

FS-8700-31 Siemens TIWAY I Driver

Бренд: FieldServer Страницы: 26

FIREWORKS 8-USING FIREWORKS

Бренд: MACROMEDIA Страницы: 472

Бренд: Qualcomm Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды